Hyundai Tucson: Engine Control System / Injector Repair procedures
| 1. |
Turn the ignition switch OFF. |
| 2. |
Disconnect the injector connector. |
| 3. |
Measure resistance between the injector terminals 1 and 2. |
| 4. |
Check that the resistance is within the specification.
Specification: Refer to “Specification”
|
|
|
In case of removing the high pressure fuel pump, high
pressure fuel pipe, delivery pipe, and injector, there may be injury
caused by leakage of the high pressure fuel. So don’t do any repair
work right after engine stops.
|
| 1. |
Turn the ignition switch OFF and disconnect the battery negative (-) cable. |
| 2. |
Release the residual pressure in fuel line.
(Refer to the Fuel Delivery System - "Release Residual Pressure in Fuel Line")
|
When removing the fuel pump fuse, a Diagnostic Trouble Code
(DTC) may occur. Delete the code with the GDS after completion of
“Release Residual Pressure in Fuel Line” work. |
|
| 3. |
Remove the delivery pipe & injector assembly.
(Refer to Fuel Delivery System - "Delivery Pipe") |
| 4. |
Remove the connector (A) and the fixing clip (B), and then separate the injector from the delivery pipe. 
|
| • |
Do not reuse the used injector fixing clip. |
|
| • |
Install the component with the specified torques. |
| • |
Note that internal damage may occur when the component is dropped. If the component has been dropped, inspect before installing. |
|
| • |
Apply engine oil to the injector O-ring. |
| • |
Do not reuse the used injector O-ring. |
|
| • |
Do not reuse the used bolt. |
|
| • |
When inserting the injector, be careful not to damage the injector tip. |
|
| • |
Do not reuse the support disc. |
| • |
Do not reuse the injector rubber washer. |
| • |
When replacing the rubber washer, the steal plate (A) part
should face the cylinder installation part and the rubber plate (B) part
should face the injector body part. |
|
| • |
Do not reuse the combustion seal.
|
|
| 1. |
Install in the reverse order of removal. |
The injector combustion seal should be replaced with new one to prevent leakage after removing the injector.
| 1. |
Remove the combustion seal (A) with a wire cutter. 
|
Grip the sealing ring carefully, pull it to form a small loop and then cut it.
Be careful not to damage the surface of the valve sleeve with the wire cutter. |
|
| 2. |
Before the assembly of the sealing ring the groove must be cleaned using a clean cloth and a brass-wire brush. 
|
The surfaces of the new sealing ring must be clean and free of grease. |
|
| 3. |
Place the seal installing guide (B) (SST No.: 09353-2B000) on the tip of the injector not to damage the injector tip (A).
Push the sealing ring (C) with thumb and index finger over the conical assembly tool until it snaps into the groove.
The complete assembly must not take longer than 2 to 3 seconds. 
|
| 4. |
To size the sealing ring the injector is first introduced
into the sizing tool (A) (SST No.: 09353-2B000) and then pressed and at
the same time rotated 180° into the sizing tool. 
|
| 5. |
Pull the injector out of the sizing tool by turning it in the reverse direction to that used for the press-in process.
|
Check that the seal ring has not been damaged during assembly to the injector and no circumferential scratches are present.
Do not reuse the combustion seal.
The seal must be completely free of grease and oil. |
|
| 6. |
Check the combustion seal (A) installation. 
|
Circuit Diagram
(M/T)
(A/T)
...
Description
Purge Control Solenoid Valve (PCSV) is installed on the surge
tank and controls the passage between the canister and the intake
manifold. It is a solenoid valve and is open when the ...
Other information:
Hyundai Tucson (LM) 2010-2015 Owners Manual: Starting the engine
WARNING
Always wear appropriate shoes when operating your vehicle. Unsuitable shoes,
such as high heels, ski boots, sandals, flipflops, etc., may interfere with your
ability to use the brake, accelerator and clutch pedals.
1.Make sure the parking brake is applied.
2.Make sure the shift lever ...
Hyundai Tucson (LM) 2010-2015 Service Manual: Cruise Control Switch Repair procedures
Removal and Installation
1.
Disconnect the battery negative terminal.
2.
Remove the driver airbag module.
(Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")
3.
Remove the steering wheel.
(Refer to Steering System - "Steering Column and Shaft")
4.
Remove the steeri ...
Injector Schematic Diagrams
Purge Control Solenoid Valve (PCSV) Description and Operation